Module 2: Footage and Clocks
Good Tile Style is planned before it is built. This module picks the best seconds of each scene, maps each subject onto the grid, and teaches the one-clock rule that keeps every tile showing the same shared moment.
Choose scenes and find the good part
Scenes in a finished Tile Style piece are short: about 1.5 to 6 seconds of screen time each. That means you do not need long clips. You need short clips with one clear, lovely thing happening: boats rocking, water moving, hands lifting a cup. When you review raw footage, watch for the stretch where the movement is steadiest and the framing is cleanest, and mark that stretch as your working section.
The head of a clip is usually setup. Someone settles into position, the camera finds its height, a hand reaches in to adjust something. Skip it. The good part almost always starts a few seconds in, which is why this course fixes a chosen in-point for every scene. In Harbor Morning, Scene A's raw clip runs much longer than the piece needs, and its chosen in-point is 0:04.0, four seconds in, where the boats are already framed and the water is already moving. Everything before that mark is warm-up and never reaches the timeline.
Be strict about quality, because the finished video is built from best takes only. A shaky or dull scene cannot be rescued by clever flips; the tiles only reveal what is already there. If a scene is weak, swap it now, while swapping costs nothing. Never plan to pad a thin piece with weak footage to hit a length. Harbor Morning runs 28 seconds because that is what its three good scenes honestly support, and yours should be sized the same way.
Subject analysis: name it and locate it
Before you schedule a single flip, do a subject analysis for every scene. Write down, in plain words, what the main subject is, and then find where that subject lives on your numbered grid. A subject that crosses tile borders is normal. What matters is knowing exactly which tiles it occupies, because those tiles get special treatment in the choreography.
In Scene B of Harbor Morning, the subject is the one boat in close view, moving gently. On the Premiere grid it occupies a 2 by 2 block at columns 3 to 4 and rows 2 to 3. Those four tiles form the subject block. They will flip together, as one piece, as the last event of Scene B's arrival, so the boat appears whole in a single moment instead of arriving in slices. Write "subject block" beside those tile numbers in your notes and never schedule them as ordinary tiles.
While you are looking, mark the dead zones too. Dead zones are the quiet areas where little changes: open sky, calm water, a plain wall. In Harbor Morning, parts of the sky and water qualify. Dead zones are where guest tiles can visit later without fighting the subject for attention, and they are also safe places to start a transition when you want a gentle opening. Finish this lesson with one line per scene in your notes: subject, its tile numbers, and its dead zones. Module 4 turns those lines directly into choreography.
The one-clock rule and the flip schedule
Here is the law that keeps a scene believable. All copies of one scene share one clock: at any moment on the timeline, every visible tile of that scene must show the same moment from the source clip. The copies start at different times, because tiles flip on one after another, so you compensate with the in-point. A copy that flips on later must start further into the source clip by exactly the same amount.
One scene, one clock
The math is one addition. Take Scene A, which starts at 0:00 on the timeline with a chosen in-point of 0:04.0 in the raw clip. A tile that flips on at 2.0 seconds into the scene uses an in-point of 0:06.0, because 4.0 plus 2.0 is 6.0. A tile that flips on at 3.5 seconds uses 0:07.5. A tile that flips on right at the scene start uses 0:04.0 unchanged. Skip this offset and each tile plays its own private timeline, so a boat crossing two tiles arrives at the border at two different times and the scene looks broken.
Plan every flip on paper before you build. Your flip schedule is a simple table: tile number, flip-on time, flip-off time if it has one, and the in-point you just calculated. Harbor Morning's schedule runs from the first wave tile at 1.2 seconds to the subject block at 16.2. Writing it first feels slow for ten minutes and saves an hour of hunting through stacked clips later, because in Premiere you will build straight from the table, row by row, without making timing decisions mid-build.
Your turn: Write your flip schedule here: for each scene, list the tile number, its flip-on time, and its in-point, using chosen in-point plus delay. Copy Harbor Morning's Scene A pattern first, then adapt it to your own footage.
Saved.
Flip pacing planner
Play with the numbers — everything updates live.
Flips per second:0
Average gap between flips (ms):0
Clicks needed:0
Scene A starts at 0:00 with a chosen in-point of 0:04.0. A tile flips on at 3.5 seconds. What in-point does its copy need?
What you can now do
- Pick short scenes and find the good part past the setup at the head of each clip.
- Name each scene's subject, locate its tiles on the grid, and mark the dead zones.
- Apply the one-clock rule: in-point equals chosen in-point plus flip delay, and write a full flip schedule before building.